1、The plunger consists of a solid spiral mandrel, tapered mandrel nose, and premium high-alloy dart.
該柱塞包括一個實心螺旋軸、錐形芯軸的機頭和優質高合金活門。

2、One that dashes, especially the plunger of an ice-cream freezer.
猛沖者猛沖的人或物，尤指冰淇淋凝固攪拌器

3、Craft of DW-series Single Hydraulic Prop′s Plunger Piece Weld
DW型單體液壓支柱柱體焊接工藝

4、The balance valve circuit is to support the weight of platen and plunger design.
回路中的平衡閥是為支撐壓板及柱塞的重量而設計的。

5、Plunger head chute different location, change the amount of oil in a different manner.
柱塞頭部斜槽的位置不同，改變供油量的方法也不同。

6、When the plunger diameter is decreased, what happens to the fill time?
當沖頭的直徑減少，填充時間會發生什么變化？

7、Cock and ball: Turn off the prop is a plunger or a ball, rotating around its own axis.
旋塞和球形：關閉件是柱塞或球，圍繞本身的中心線旋轉。

8、The most common type USES spring tension and pressure against a plunger to maintain the pressure.
最常用的一種回壓閥使用彈簧張力和對柱塞的壓力來保持壓力。

9、The plunger or piston of a force pump or hydraulic press.
活塞壓力泵或水壓機內的柱塞或活塞

10、Figure 1 shows the various seals and traveling valve in the plunger position.
圖1所示是各種密封和游動閥在柱塞上的位置。

11、The solenoid plunger pulls the vent valve down, blocking off the passage to the charcoal canister.
電磁柱塞拉下通氣閥，堵住通向活性碳罐的通路。

12、This is often tail - fin shape plunger due to excessive thickness.
這往往是柱塞尾部翅形體過厚所致。

13、The radiated sound field of ring plunger is analyzed.
研究了環狀活塞聲源輻射聲場的特性。

14、With the car upside - down, the ball forces the plunger to seat against the guide plate.
當汽車傾倒時，滾珠迫使柱塞落在支承板上。

15、The plunger should be withdrawn from sleeve.
柱塞應從套筒里抽出來。

16、This would free the spring, and up would pop a plunger to announce the bird was ready.
這樣彈簧就可被釋放并向上彈出一個活塞以宣告鳥類已經烤熟。

17、G. Slowly advance the needle while gently withdrawing the plunger of the syringe.
在輕輕回抽注射器的同時緩慢進針。

18、The plunger or piston of a force pump or hydraulic press
活塞壓力泵或水壓機內的柱塞或活塞

19、The position of the plunger cylinder is measured by a linear position transducer.
活塞桿的位置是通過一個線性位置傳感器測量的。

20、Failure Analysis of the Plunger of Plunger Pump OPI-1800AWS
OPI-1800AWS柱塞泵柱塞失效分析

21、The plunger extruder is developed for suiting to process UHMWPE pipes, rods and profiles, etc.
研制了適于加工UHMWPE管材、棒材及異型材等制品的柱塞式擠出機。

22、R2 is the point of signal transfer between plunger and barrel.
R2是頂針與套殼體之間的信號傳輸點。

23、Turn off the prop is a plunger or a ball, rotating around its own axis.
關閉件是柱塞或球，圍繞本身的中心線旋轉。

24、Rubber plunger should not be rubber thread, rubber chipping, foreign impurity, spray frost.
橡膠活塞應無膠絲、膠屑、外來雜質、噴霜。

plunger翻譯